-
Edge Position Control Systems(Sensors)
- Sensor / Electric Type Diagram
- Autowide Sensor AWE280A
- Photohead PH22VAS for vacuum environments
- High-temperature EPC sensor HE120A (for transparent webs)
- Ultrasonic Sensor UH05
- CMOS Linear Sensor SLH30
- Design Position Control DPC
- PHOTOHEAD PH16B / PH21
- PHOTOHEAD PH22
- ULTRASONIC SENSOR UH01 series
- Ultrasonic Autowide Sensor UHW051
- Ultrasonic Autowide Sensor UHW280
- Ultrasonic Autowide Sensor UHW500 / 700
- PHOTOHEAD PH30 / PH31
- LINE FOLLOWER HEAD LH19
- LINE FOLLOWER HEAD LH110
- LINE FOLLOWER HEAD LH500
-
Edge Position Control Systems(Electric type)
- Sensor / Electric Type Diagram
- Guide roller mechanism (Electric type)
- AC servo actuator A353
- AC servo actuator A032
- AC servo actuator A152-□□□-20
- Motor-Driven Actuator K50 K50/A
- Liteguide Controller AE550/AE560
- Linear Actuator K300-200-20
- Compact Guide Roll Mechanism PGR series
- Compact Guide Roll Mechanism LCD series
- Guide Roll Mechanism
- Liteguide Controller AE1000
- Motor-Driven Actuator K12 series
- Motor-Driven Actuator K62 K62/A
- Motor-Driven Actuator K80
-
Edge Position Control Systems(Hydraulic type)
-
EPC related components
-
Tension Control Systems
- Tension Control System Diagram
- Intrinsically safe explosion-proof MB tension sensor
- MJ tension sensor (for vacuum environment) MJ**VAS
- MJ tension sensor (for vacuum environment) MJ**V
- Tension Controller TC920V
- Tension Controller TC680A/D
- Open loop Tension Control System TCD030T
- Open loop Tension Control System TCD050
- Tension Meter TM310T
- Tension Meter TM340
- MG Tension Sensor
- MJ Tension Sensor
- CJ Tension Sensor
- MB Tension Sensor
- Electro-Pneumatic Converter EN40
- Other related equipment
-
Automaic Register Control Systems
-
Print-to-cut Register Control Systems
-
Other Related Equipment
Servoguide Mark-Ⅳ D-Series PNEUMATIC-HYDRAULIC TYPE
Overview
The Servoguide MK-IV is a new type of hydraulic controller which embodies our long experience and technology in the field of web control.
The Servoguide MK-IV.D is a pneumatic-hydraulic Edge Position Control(EPC) device. The edge sensors are pneumatic, which gives them an extremely simple structure, while the controller is a robust, yet highly responsive, hydraulic unit. Control is precise and maintenance is simple.
D053 Low load type
Model D053, priced lowest among the Servoguide series, is a controller for low loads.
D121 Syngle type
Model D121 is the standard model of the Servoguide MK-IV series, which can be used for most machines.
D226 Twin type
Two Servoguide MK-IV controllers are mounted on one hydraulic pump unit in the model D226. Economical and compact instrumentation can be obtained when more than one EPC system(eg. laminator line, multi-stage guide roll, etc.) is installed nearby.
D721 High load-type
Model D721 is a high-power Servoguide which can be applied for high loads and high-speed lines.
Feature
- Compact and inexpensive.
- Excellent control accuracy (control within ±0.1mm according to installation conditions).
- No contact between sensor and web.
- Very easy installation and maintenance.
- Large operating force and high sensitivity and accuracy.
- All hydraulic devices are incorporated in the oil reservoir, thus eliminating oil leakage.
- Quiet operation due to the special construction that prevents noise emission
(Operating noise level : below 65 dB (A)). - Use of a long-Iife and easy-to-maintain non-contact rotary blower allows clean air to be supplied.
- Use of a general-purpose motor makes all models explosion proof and increases safety.
System Components
AC〔AUTO-CENT〕REMOTE AUTO / CENT SWITCHING MODE
This system is available with centering operation as well asautomatic operation. The reel or the guide roll stand is automatically restored to the center position by selecting CENT with the selector switch when setting a mill roll, changing the width of a wed, or splicing webs.
AM〔AUTO-MAN〕REMOTE AUTO / MAN SWITCHING MODE
In this system, the Servoguide MK-IV. D controller can be remotely switched off during automatic operation or the reel stand can be moved right and left, when setting a mill roll or splicing webs.
Specifications
D053
| Type | Low load |
|---|---|
| Max operating pressure (Mpa) | 1 |
| Pump capacity (L/min) | 2.0 (No-load) |
| Pump type | Fix displacement |
| Motor Output (W) | 200 |
| Max. operating force (kN) Cylinder bore (mm) |
50 ···· 1.9 80 ···· 4.9 |
| Max. operating speed with no load (mm/s) Cylinder bore (mm) |
50 ···· 20 80 ···· 8 |
D121
| Type | Single standard | |
|---|---|---|
| Max operating pressure (Mpa) | 1.5 | |
| Pump capacity (L/min) | 4.2 (No-load) | |
| Pump type | Fix displacement | |
| Motor Output (W) | 400 | |
| Max. operating force (kN) Cylinder bore (mm) |
50 ···· 2.9 80 ···· 7.4 |
|
| Max. operating speed with no load (mm/s) Cylinder bore (mm) |
50 ···· 34 80 ···· 13 |
D226
| Type | Twin standard | |
|---|---|---|
| Max operating pressure (Mpa) | 1.5 | |
| Pump capacity (L/min) | 4.2 (No-load) | |
| Pump type | Fix displacement | |
| Motor Output (W) | 400 | |
| Max. operating force (kN) Cylinder bore (mm) |
50 ···· 2.9 80 ···· 7.4 |
|
| Max. operating speed with no load (mm/s) Cylinder bore (mm) |
50 ···· 20 80 ···· 8 |
D721
| Type | High load | |
|---|---|---|
| Max operating pressure (Mpa) | 2.5 | |
| Pump capacity (L/min) | 9(60Hz), 7.5(50Hz) (No-load) |
|
| Pump type | Variable displacement | |
| Motor Output (W) | 750 200 |
|
| Max. operating force (kN) Cylinder bore (mm) |
80 ···· 12.3 | |
| Max. operating speed with no load (mm/s) Cylinder bore (mm) |
80 ···· 30 |
Contact Us
Please use this form to submit your inquiries, feedback and/or requests to NIRECO.
