-
Edge Position Control Systems(Sensors)
- Sensor / Electric Type Diagram
- Autowide Sensor AWE280A
- Photohead PH22VAS for vacuum environments
- High-temperature EPC sensor HE120A (for transparent webs)
- Ultrasonic Sensor UH05
- CMOS Linear Sensor SLH30
- Design Position Control DPC
- PHOTOHEAD PH16B / PH21
- PHOTOHEAD PH22
- ULTRASONIC SENSOR UH01 series
- Ultrasonic Autowide Sensor UHW051
- Ultrasonic Autowide Sensor UHW280
- Ultrasonic Autowide Sensor UHW500 / 700
- PHOTOHEAD PH30 / PH31
- LINE FOLLOWER HEAD LH19
- LINE FOLLOWER HEAD LH110
- LINE FOLLOWER HEAD LH500
-
Edge Position Control Systems(Electric type)
- Sensor / Electric Type Diagram
- Guide roller mechanism (Electric type)
- AC servo actuator A353
- AC servo actuator A032
- AC servo actuator A152-□□□-20
- Motor-Driven Actuator K50 K50/A
- Liteguide Controller AE550/AE560
- Linear Actuator K300-200-20
- Compact Guide Roll Mechanism PGR series
- Compact Guide Roll Mechanism LCD series
- Guide Roll Mechanism
- Liteguide Controller AE1000
- Motor-Driven Actuator K12 series
- Motor-Driven Actuator K62 K62/A
- Motor-Driven Actuator K80
-
Edge Position Control Systems(Hydraulic type)
-
EPC related components
-
Tension Control Systems
- Tension Control System Diagram
- Intrinsically safe explosion-proof MB tension sensor
- MJ tension sensor (for vacuum environment) MJ**VAS
- MJ tension sensor (for vacuum environment) MJ**V
- Tension Controller TC920V
- Tension Controller TC680A/D
- Open loop Tension Control System TCD030T
- Open loop Tension Control System TCD050
- Tension Meter TM310T
- Tension Meter TM340
- MG Tension Sensor
- MJ Tension Sensor
- CJ Tension Sensor
- MB Tension Sensor
- Electro-Pneumatic Converter EN40
- Other related equipment
-
Automaic Register Control Systems
-
Print-to-cut Register Control Systems
-
Other Related Equipment
Guide roller mechanism (Electric type)

Overview
The guide roller mechanism is used to correct the meandering of the traveling web. The guide roller mechanism is available as either a center-pivot system or an end-pivot system.
Feature
NIRECO provides the guide roller mechanism suited to the requirements of the web quality, width, tension, correction quality and speed and installation conditions by applying its extensive
Center-pivot system(LCD)
The center of rotation is the center of the planar extending surface of the web on the side where it enters the guide roller. This method may be applied for webs which are likely to break or have a permanent distortion due to the tension difference between both edges of the web, i.e., non-elastic materials such as paper, newsprint paper, coating paper, metal, foil, cellulose, acetate, fragile plastics, etc.

Center-pivot system diagram

Center-pivot system specification
Model | Applications | Load | Roller material | Maximum tension N | Roller surface length mm |
---|---|---|---|---|---|
LCD-B | For business forms (has built-in width extender) | Low | Aluminum | 250 | 550,610 |
LCD-01 | Offset rotary press | Intermediate | Aluminum | 1000 | 1000,1100 |
LCD-L | General use | Low | Aluminum or steel | 250 | 300~650 |
LCD-M | General use | Intermediate | Aluminum or steel | 500 | 500~800 |
End-pivot system(LED)
The end pivot system comes in two forms: the dual-roller S-wrap type and the single-roller 90°-wrap type. The dual-roller S-wrap end-pivot system is used in the middle of the web line, while the single-roller 90°-wrap end pivot system is installed at the point where the web makes a 90-degree change in direction.

End-pivot system diagram

End-pivot type specification
Model | No. of roll | Wrap type | Load | Roller material | Maximum tension N | Roller surface length mm |
---|---|---|---|---|---|---|
LED-L1 | For business forms (has built-in width extender) | S-Wrap | Low | Aluminum or steel | 250 | 280~650 |
LES-L1 | 1 | 90°-Wrap | Low | Aluminum or steel | 250 | 280~650 |
LED-M | 2 | S-Wrap | Intermediate | Aluminum or steel | 1000 | 800~1600 |
LES-M | 1 | 90°-Wrap | Intermediate | Aluminum or steel | 1000 | 800~1600 |
Contact Us
Please use this form to submit your inquiries, feedback and/or requests to NIRECO.